CPS Battery chargers

Models - 12V/06A, 12V/10A, 24V/03A & 24V/05A

Compact, lightweight and aesthetic, CRISTEC CPS (Selective Programmable Charge) chargers offer you all the safety and convenience that advanced technology in the battery charging area can bring you.

CPS Chargers… Autonomy.

The whole CPS range provides a specific charge to the battery which is fully compliant with all of the battery manufacturer’s specifications. Entirely automatic, with built in charge distributor, these chargers can remain permanently connected to the battery in complete safety and do not have to be disconnected when starting the engine.

CPS Chargers… Performance.

The timed boost function may be selected depending on the charger mode of use.

CPS Chargers… Protection.

The equipment is protected against polarity reversal and short-circuits ; the entire CRISTEC CPS range is protected for marine use.

Electrical specifications

Voltage, frequency

• Input voltage: 115 or 230 Vac ± 15% by internal switch.
• Automatic input frequency from 47 to 63 Hz.
• Output voltage (depending on particular model):12 or 24 Vdc ± 1%.
• Internal potentiometer allows output voltage to be adjusted.

Charge

• Three automatic charge cycles: boost, absorption, floating.
• Programmable timed boost by internal dip switch.
• Charge distributor incorporated into each battery output (2 outputs).
• Selecting of the level of charge according to the type of battery by internal dip switch (Lead/Antimony ; Lead/ Calcium).
• Front display: LED for mains present and LED for charge status (boost/absorption, intermittent, floating, continuous).

Protection

Integrated protection against short-circuits and polarity reversal. Removable fuses on input and output.

Environment

• Natural convection.
• Operating temperature: - 10 to + 40°C.
• Storage temperature: - 20 to + 70°C.

Features

Suitable for use with AC generators.

Can be used as a DC regulated and filtered power supply.

Standards

CE standards: EN 50081-1, EN 50082-1, EN 55011, EN 55022, EN 60950.

Mechanical characteristics

• Standard presentation in IP22 case with drip-proof cover.
• Epoxy finish matt black RAL 9011 and grey RAL 7035, salt atmosphere resistant.
• Electronics card given tropicalised coating after mounting components.
• Water-repellent varnish.
• Supplied with mains cable and 230Vac plug.
• Connection terminals to allow a direct cabling of the battery cables (-,+,+) without opening the charger.

Data Sheet

Multiple outputs: Charge 3 batteries simultaneously

CPS3 battery chargers have 3 independent outputs (except models > 80A) which canindividually deliver nominal output current. One of these outputs is designed for matching specific engine battery requirements for marine application.

The built-in battery isolator on each battery bank means the batteries stay permanently connected to the charger and there is no need to disconnect them during engine startup.

The CRISTEC CPS3 battery chargers are the only ones available on the market with an extra terminal to connect an additional external battery isolator for connecting up to 6 independent battery banks (3 from the charger and 3 from the battery isolator).

CRISTEC recommends using a voltage drop free isolator. Please referto the CRISTEC RCE battery isolator range.

Choose your charging curve: Safety and freedom

On CPS3 chargers the BOOST phase is particularly safe as it is not only timed but also current controlled. In the event of a cut in the charger power-supply the charging cycle does not reset. The 3-step charge mode being faster (BOOST, ABSORPTION and FLOATING) it is particularly useful when you run out of time to charge the batteries (charger powered from a generator, short stay in the marina, etc.).

It is possible to interrupt the Boost phase with an internal switch for specific applications where this function is not required: wintering, self-maintaining battery charge or when the charger is used as direct current regulated and filtered power supply.

Choose your battery type: Made-to-measure battery charging

As your choice regarding battery technology is extensive, you have to make sure charging characteristics comply with your specific battery type. CPS3 battery chargers have internal selectors for setting the charge level in compliance with the battery technology and application : there are 11 settings such as Lead-sealed, Calcium-Lead, AGM, Gel, etc.

Universal AC powering: Worldwide use

The AC input voltage and frequency auto-ranging – from 85 to 265 VAC and from 47 to 65 Hz – guarantees batteries can be charged anywhere (in Europe and in the USA), from commercial Mains or generators, even when available power is limited (end of pontoon, foreign network, etc.). Except model 24V/150A 400VAC 3 phases

The strength of innovation

CPS3 battery chargers : the answer to constantly changing requirements in a climate of increasingly stricter standards.

Multiple outputs: Charge 3 batteries simultaneously

CPS3 battery chargers have 3 independent outputs (except models > 80A) which can individually deliver nominal output current. One of these outputs is designed for matching specific engine battery requirements for marine application. The built-in battery isolator on each battery bank means the batteries stay permanently connected to the charger and there is no need to disconnect them during engine startup.

The CRISTEC CPS3 battery chargers are the only ones available on the market with an extra terminal to connect an additional external battery isolator for connecting up to 6 independent battery banks (3 from the charger and 3 from the battery isolator).

CRISTEC recommends using a voltage drop free isolator. Please referto the CRISTEC RCE battery isolator range.

Choose your charging curve: Safety and freedom

On CPS3 chargers the BOOST phase is particularly safe as it is not only timed but also current controlled. In the event of a cut in the charger power-supply the charging cycle does not reset.

The 3-step charge mode being faster (BOOST, ABSORPTION and FLOATING) it is particularly useful when you run out of time to charge the batteries (charger powered from a generator, short stay in the marina, etc.).

It is possible to interrupt the Boost phase with an internal switch for specific applications where this function is not required: wintering, self-maintaining battery charge or when the charger is used as direct current regulated and filtered power supply.

Choose your battery type: Made-to-measure battery charging

As your choice regarding battery technology is extensive, you have to make sure charging characteristics comply with your specific battery type. CPS3 battery chargers have internal selectors for setting the charge level in compliance with the battery technology and  application : there are 11 settings such as Lead-sealed, Calcium-Lead, AGM, Gel, etc.

Universal AC powering: Worldwide use

The AC input voltage and frequency auto-ranging – from 85 to 265 VAC and from 47 to 65 Hz – guarantees batteries can be charged anywhere (in Europe and in the USA), from commercial Mains or generators, even when available power is limited (end of pontoon, foreign network, etc.). Except model 24V/150A 400VAC 3 phases

The strength of innovation

CPS3 battery chargers : the answer to constantly changing requirements in a climate of increasingly stricter standards.

Special coating: peace of mind

The charger electronic boards are coated with waterproof and tropicalised varnish. An anti-drip covering protects the charger from water ingress.The entire charger casing paint is specifically coated to prevent corrosion.

Managing technology: high performance

The latest HF technology and COS PHI 1 regulation (integrated PFC – Power Factor Correction) ensure nominal charger operation in the event of wide input fluctuation. As AC charger input consumption is low you economise generator power.

In-built protection: reliability

The CPS3 battery chargers have numerous in-built protection devices (polarity reversal, short-circuits through removable fuses, over-heating, etc.) ensuring a long charger life.

Parallel-mount: flexibility

You can parallel-mount our chargers thereby multiplying the output current (2 off 12V/60A chargers will deliver 12V/120A). You can parallel-mount up to 6 chargers preferably the same size. The power-sharing function is active if only one single output is used per charger (on models 12V/80A, 12V/100A, 24V/60A, 24V/75A, 24V/120A, 48V/30A and 48V/60A).

Data Sheet